Keurig Bolt Manual

The Keurig Bolt is a high-performance single-serve coffee brewing system designed for office and commercial use. It features rapid brewing technology, multiple cup size options, programmable settings, energy-saving mode, descaling alerts, removable drip tray, and compatibility with K-Cup pods. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to Water Source 7. Brewing Coffee 8. Maintenance Features 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: High-speed brewing system, programmable controls, removable water reservoir, drip tray, power button, display screen, brew size selector.

Feature	Description
Brewing System	High-pressure pump for optimal extraction
Cup Size Options	6oz, 8oz, 10oz, 12oz programmable sizes
Water Reservoir	Removable 60oz capacity with handle
Display Screen	LCD with brewing status and alerts
Energy Saver Mode	Automatically enters standby after 2 hours
Descaling Alert	Automatic notification when descaling needed
Drip Tray	Removable and adjustable for tall mugs
Power Button	Turns brewer on/off
Brew Button	Initiates brewing cycle
Cup Size Selector	Programs preferred brew size

Installation

Unpack and inspect contents. Place on stable, level surface.

Remove packaging materials and protective tape from all components.
Place brewer on counter away from heat sources and direct sunlight.
Install water reservoir: Lift and snap into place on rear of brewer.
Plug into grounded electrical outlet.

WARNING! Ensure proper ventilation around brewer. Do not place near water sources.

First-Time Setup

Power on brewer; follow initial setup procedure.

Prime the system: Fill reservoir with fresh water, run several brewing cycles without pod.
Program cup sizes: Use CUP SIZE button to set preferred volumes.
Set energy saver: Access menu to enable/disable auto standby.
Calibrate temperature: Use temperature settings for optimal brewing.

CAUTION! Use only filtered or bottled water to prevent mineral buildup.

Specifications

Dimensions: 10.5" W x 13.2" D x 13.8" H
Water Reservoir: 60oz removable capacity
Brew Sizes: 6oz, 8oz, 10oz, 12oz programmable
Brew Time: Under 60 seconds per cup
Power: 1500W, 120V AC, 60Hz
Compatibility: All K-Cup pod varieties
Display: Backlit LCD with status indicators
Weight: 8.5 lbs empty
Warranty: 1-year limited warranty

Controls and Settings

Access settings via control panel buttons. Front Panel: POWER, BREW, CUP SIZE, MENU.

Display Indicators: Ready to brew, heating, brewing, add water, descale needed.

Programmable Settings: Cup size (6oz, 8oz, 10oz, 12oz), energy saver (on/off), temperature (low/medium/high), auto-off timer (15min-4hr). Maintenance: Descaling mode, factory reset, water filter reminder.

Connecting to Water Source

For direct water line connection (optional): Use water line kit.

Turn off brewer and unplug from electrical outlet.
Connect water line to rear water inlet port.
Connect other end to filtered water source.
Turn on water supply and check for leaks.

Tip: Use only Keurig-approved water line kits for direct connection.

Brewing Coffee

Supports all K-Cup pod varieties including coffee, tea, and hot cocoa.

Lift handle: Open brewer head fully.
Insert pod: Place K-Cup in pod holder.
Close handle: Firmly lower until it locks.
Select size: Press CUP SIZE for desired volume.
Place cup: Position mug on drip tray.
Brew: Press BREW button to start cycle.
Remove pod: Lift handle after brewing to eject used pod.

WARNING! Do not open brewer during brewing cycle. Hot liquid may cause burns.

Maintenance Features

Descaling Alert: Automatic notification when mineral buildup detected. Water Filter Reminder: Programmable filter replacement alert. Auto-Off: Energy saving mode reduces power consumption.

Care & Cleaning

Unplug before cleaning. Wipe exterior with damp cloth. Clean water reservoir weekly with mild detergent. Run descaling solution every 3-6 months.

CAUTION! Do not immerse brewer in water. Use only Keurig descaling solution.

Regulatory Information

UL Listed: Complies with UL 197 safety standards. FCC Part 15: Class B digital device. Energy Star: Meets energy efficiency guidelines. Copyright © 2025 Keurig; trademarks of Keurig Green Mountain, Inc. For support, visit www.keurig.com or contact 1-866-901-BREW.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Brewer won't power on	Power connection	Check electrical outlet; ensure power cord securely plugged in.
No water flow	Clogged needle/reservoir	Check water reservoir placement; clean exit needle with paper clip.
Weak coffee	Mineral buildup	Descale brewer; check water filter if installed.
Error message on display	System error	Unplug for 2 minutes, then restart; contact service if persistent.
Leaking water	Loose connections	Check reservoir seal; ensure all connections tight.

Reset: Unplug for 2 minutes to reset electronic controls.

Service: 1-866-901-BREW; www.keurig.com