Keurig Coffee Maker Parts Manual

The Keurig Coffee Maker is a single-serve brewing system designed for convenient coffee preparation at home or office. This manual covers essential parts identification, maintenance procedures, troubleshooting, and replacement guidelines for various Keurig models. Below are key sections covering parts overview, assembly, cleaning, maintenance, and troubleshooting.

Parts Overview

Key components: Water reservoir, Brewing chamber, K-cup holder, Drip tray, Control panel, Power base, Heating element, Pump assembly.

Assembly Instructions

Unpack and verify all components. Place on stable, level surface.

1. Attach water reservoir: Align with main unit and press until secure.
2. Install drip tray: Slide into position at base of unit.
3. Connect power cord: Plug into rear power port and wall outlet.
4. Prime system: Fill reservoir, run initial water cycle without K-cup.

WARNING! Ensure unit is unplugged during assembly. Handle with care to avoid damage to components.

Cleaning and Maintenance

Regular maintenance ensures optimal performance and longevity.

1. Daily cleaning: Wipe exterior with damp cloth, empty drip tray.
2. Weekly cleaning: Remove and wash water reservoir, clean K-cup holder.
3. Monthly descaling: Use Keurig descaling solution as per instructions.
4. Needle cleaning: Use paper clip to clear clogged needles.

CAUTION! Unplug unit before cleaning. Do not immerse in water.

Specifications

• Power Requirements: 120V AC, 60Hz, 1470W
• Water Reservoir Capacity: 48-60 oz (varies by model)
• Brew Sizes: 6, 8, 10 oz (programmable)
• Heat Up Time: Less than 3 minutes
• Dimensions: Varies by model (typically 13" H x 10" W x 13" D)
• Weight: 5-7 lbs
• Brew Temperature: 192°F (89°C)
• Pressure: High-pressure pump system
• Compatibility: All Keurig K-cup pods

Controls and Functions

Control panel includes power button, brew size selection, brew button, and display indicators.

Basic Operation: POWER (on/off), BREW SIZE (6/8/10 oz), BREW (start cycle), ADD WATER (indicator light).

Advanced Features: Auto-off (programmable 1.5-2 hours), Strength Control (varies brew time), Hot Water (for tea/cocoa), Programmable settings (clock, auto-brew). Display shows ready status, descale alert, water level warnings.

Water Reservoir System

Removable reservoir with handle and lid. Features water level indicator and filter compatibility.

1. Remove reservoir by lifting straight up
2. Fill with fresh, cold water (max fill line)
3. Replace securely on main unit
4. Optional: Install water filter for improved taste

Tip: Use filtered water to reduce mineral buildup and descaling frequency.

Brewing Mechanism

K-cup loading and brewing process:

1. Lift handle to open brewing chamber
2. Insert K-cup pod (any orientation)
3. Close handle firmly until it locks
4. Place cup on drip tray
5. Select brew size and press BREW
6. Brewing completes in approximately 1 minute
7. Lift handle to eject used pod

WARNING! Do not force handle closed. Ensure K-cup is properly seated.

Descaling Procedure

Required every 3-6 months depending on water hardness.

1. Empty water reservoir
2. Add Keurig descaling solution to reservoir
3. Fill remainder with water
4. Place large mug on drip tray
5. Initiate descale mode (varies by model)
6. Run multiple brew cycles until solution depleted
7. Rinse reservoir and run several water-only cycles

CAUTION! Use only Keurig-approved descaling solution.

Care & Maintenance

Unplug before cleaning. Wipe exterior with soft, damp cloth. Clean removable parts with mild soap and water.

CAUTION! Do not use abrasive cleaners. Avoid getting water in electrical components.

Regulatory Information

UL Listed: Certified for safety standards. FCC Part 15: Class B digital device compliance. Energy Star: Meets energy efficiency guidelines. Copyright © 2025 Keurig Green Mountain, Inc. All rights reserved. For support, visit www.keurig.com or contact 1-866-901-2739.

Troubleshooting

Reset: Unplug for 2 minutes, then restart.

Service: 1-866-901-2739; www.keurig.com