keurig k300 manual pdf

The Keurig K300 is a single-serve coffee brewing system designed for home use, featuring K-Cup pod compatibility, multiple brew sizes, removable water reservoir, programmable settings, descaling alerts, and energy-saving auto-off function. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Brew chamber, Removable water reservoir, Control panel, Drip tray, Power button, Brew size buttons.

Installation

Unpack and inspect contents. Place on clean, level surface.

1. Remove all packaging materials and stickers.
2. Wash removable water reservoir with warm, soapy water.
3. Place brewer on stable counter away from heat sources.
4. Fill reservoir with fresh cold water and reinstall.
5. Plug into 120V AC power outlet.

WARNING! Do not use without water. Keep away from children. Ensure proper ventilation around brewer.

First-Time Setup

Prime the brewing system before first use.

1. Press power button to turn on brewer.
2. Wait for "Add Water" light to turn off.
3. Place mug on drip tray.
4. Lift and close handle without K-Cup pod.
5. Select largest brew size and press brew button.
6. Repeat process 2-3 times to prime system.
7. Brewer is now ready for first beverage.

CAUTION! Hot water and steam may cause burns. Keep hands clear during brewing cycle.

Specifications

• Dimensions: 13.2" H x 10.2" W x 13.5" D
• Water Reservoir: 48 oz capacity
• Brew Sizes: 6oz, 8oz, 10oz
• Power: 120V AC, 60Hz, 1470W
• Brew Time: Under 1 minute
• Temperature: 192°F brewing temperature
• Weight: 7.5 lbs
• Auto-Off: 90 seconds
• Warranty: 1 year limited

Controls and Settings

Control panel features: Power button, Brew button, Brew size selection, Add Water indicator, Descaling indicator.

Programming: Hold brew size button for 3 seconds to set default size. Power indicator shows heating status (flashing when heating, solid when ready).

Brew Settings: 6oz (small), 8oz (medium), 10oz (large). Indicators: Red light for add water, Orange light for descaling needed. Energy Saver: Automatically powers off after 90 seconds of non-use.

Brewing Process

Simple three-step brewing with K-Cup pods.

1. Lift handle to open brew chamber.
2. Insert K-Cup pod into pod holder.
3. Close handle firmly until it clicks.
4. Place mug on drip tray (minimum 5oz capacity).
5. Select desired brew size.
6. Press brew button to start cycle.
7. Brewing completes automatically.
8. Lift handle to remove used pod.

Tip: For best results, use filtered water and store K-Cups in cool, dry place.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Daily: Wipe exterior with damp cloth.
2. Weekly: Remove and wash water reservoir.
3. Monthly: Clean drip tray and pod holder.
4. As needed: Descale when indicator lights.
5. Exterior: Use only mild detergent, no abrasives.
6. Interior: Run vinegar solution monthly to clean.

CAUTION! Unplug brewer before cleaning. Never immerse in water.

Descaling Procedure

Required every 3-6 months or when descale light illuminates.

1. Prepare descaling solution or white vinegar.
2. Empty water reservoir and fill with descaling solution.
3. Place large bowl or measuring cup on drip tray.
4. Press and hold 8oz and 10oz buttons for 3 seconds.
5. Press brew button to start descaling cycle.
6. Repeat brewing until reservoir is empty.
7. Rinse reservoir and fill with fresh water.
8. Run multiple brew cycles with clean water to rinse.

WARNING! Use only Keurig descaling solution or food-grade vinegar. Rinse thoroughly.

Regulatory Information

UL listed: Certified for safety standards. FCC Part 15: Class B digital device compliance. Copyright © Keurig Green Mountain, Inc. Energy Star: Meets energy efficiency guidelines. For support, visit www.keurig.com or contact 1-866-901-2739.

Troubleshooting

Reset: Unplug for 2 minutes then restart.

Service: 1-866-901-2739; www.keurig.com