Keurig K50 Coffee Maker Manual

The Keurig K50 is a single-serve coffee brewing system featuring K-Cup pod compatibility, multiple brew sizes, removable water reservoir, automatic shut-off, descaling function, brew strength control, and energy saving mode. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Brewing Process 7. Maintenance & Cleaning 8. Descaling Procedure 9. Regulatory Information 10. Troubleshooting

Features at a Glance

Key components: K-Cup pod holder, Water reservoir, Drip tray, Control panel, Power button, Brew size buttons.

Feature	Description
Water Reservoir	48 oz removable reservoir with handle
Brew Sizes	6 oz, 8 oz, 10 oz cup options
Brew Strength	Regular and Strong settings
Auto Off	Automatic shut-off after 90 seconds
Energy Saver	Reduces energy consumption
Descale Indicator	Alerts when descaling is needed
Drip Tray	Removable with adjustable height
K-Cup Holder	Compatible with all K-Cup pods
Power Button	Main power control
Brew Button	Starts brewing process

Installation

Unpack and inspect contents. Place on clean, level surface.

Remove all packaging materials from coffee maker.
Wash removable water reservoir with warm, soapy water.
Place drip tray in position and ensure it's secure.
Plug into 120V AC power outlet.

WARNING! Do not operate without water in reservoir. Keep away from water sources to prevent electrical shock.

First-Time Setup

Prime the brewing system before first use.

Fill water reservoir with fresh cold water.
Place mug on drip tray.
Press power button to turn on.
Lift and close handle without K-Cup to run water through system.
Repeat priming process 2-3 times.

CAUTION! Use only K-Cup pods. Do not use ground coffee without proper accessory.

Specifications

Dimensions: 13.3" H x 10.1" W x 13.0" D
Water Reservoir: 48 oz capacity
Brew Sizes: 6 oz, 8 oz, 10 oz
Power: 120V AC, 60Hz, 1470W
Auto Off: 90 seconds
Weight: 8.5 lbs
Brew Time: Under 1 minute
Compatibility: All K-Cup pods

Controls and Settings

Control Panel: Power button, Brew size buttons (6oz, 8oz, 10oz), Add Water indicator, Auto Off indicator.

Brew Strength Control: Press and hold 6oz button for 3 seconds to toggle between Regular and Strong brew.

Settings: Auto Off (always enabled), Brew size selection, Brew strength, Energy saver mode.

Brewing Process

Simple one-cup brewing with K-Cup pods.

Lift handle to open K-Cup holder.
Insert K-Cup pod into holder.
Close handle firmly.
Place mug on drip tray.
Select brew size (6oz, 8oz, 10oz).
Press brew button to start.
Brewing completes automatically.

Tip: For hotter coffee, run a water-only cycle first to pre-heat the system.

Maintenance & Cleaning

Regular cleaning ensures optimal performance.

Daily: Wipe exterior with damp cloth.
Weekly: Clean water reservoir and drip tray.
Monthly: Descale as needed.
As needed: Clean needle that punctures K-Cup.

CAUTION! Unplug before cleaning. Never immerse coffee maker in water.

Descaling Procedure

Descale when Add Water light flashes or every 3-6 months.

Fill reservoir with 16 oz white vinegar and 16 oz water.
Place large mug on drip tray.
Press and hold 8oz and 10oz buttons for 3 seconds.
Press brew button to start descale cycle.
Repeat until reservoir is empty.
Rinse by running 2-3 reservoirs of clean water through system.

Regulatory Information

Troubleshooting

Symptom	Possible Cause	Corrective Action
No power	Power cord/outlet	Check power cord connection; test outlet; ensure power button is on.
No water flow	Water reservoir/needle	Ensure reservoir is seated properly; check for clogs in needle.
Weak coffee	Brew strength setting	Change to Strong brew setting; use smaller cup size.
Leaking water	Seals/reservoir	Check reservoir placement; inspect seals for damage.
Descale light on	Mineral buildup	Perform descaling procedure; use filtered water.

Reset: Unplug for 2 minutes, then restart.

Service: 1-866-901-2739; www.keurig.com