Keurig Model K140 Manual

The Keurig Model K140 is a single-serve coffee brewing system featuring K-Cup pod compatibility, multiple brew sizes, removable water reservoir, automatic shut-off, descaling alert, programmable clock, strength control, hot water dispenser, and drip tray with removable reservoir. Powered by 120V AC, 60Hz. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

Features at a Glance

Key components: Brew chamber, Water reservoir, Control panel, Drip tray, K-Cup holder, Power button.

Installation

Unpack and inspect contents. Place on clean, level surface.

1. Remove packaging materials and stickers from all components.
2. Fill water reservoir with fresh cold water and reinstall.
3. Plug into grounded electrical outlet.
4. Prime the brewing system by running water through without K-Cup.

WARNING! Do not use without water in reservoir. Keep away from heat sources and moisture.

First-Time Setup

Power on brewer; follow initial setup procedure.

1. Prime the system: Press power button, place mug, press brew button without K-Cup.
2. Set clock: Use clock button to set current time.
3. Program brew sizes: Use small/medium/large buttons to set preferred volumes.
4. Test brew: Insert K-Cup and perform test brew cycle.

CAUTION! First few brews may produce unusual taste due to manufacturing residues.

Specifications

• Dimensions: 13.5" H x 10.2" W x 13.5" D.
• Water Reservoir: 48oz capacity.
• Brew Sizes: 6oz, 8oz, 10oz programmable.
• Brew Time: Under 1 minute per cup.
• Power: 120V AC, 60Hz, 1470W.
• Weight: 8.5 lbs.
• K-Cup Compatibility: All K-Cup pod varieties.
• Auto Shut-off: 2 hours after last brew.
• Warranty: 1 year limited warranty.

Controls and Settings

Control Panel: Power button, Small/Medium/Large brew buttons, Strength control, Hot water button, Clock set.

Indicator Lights: Power, Add water, Descaling, Heating, Ready to brew.

Brew Size Programming: Press and hold desired brew size button until light flashes. Strength Control: Press strength button to toggle between regular and strong brew settings. Clock Setting: Press and hold clock button, use brew size buttons to adjust time. Hot Water: Press hot water button for hot water dispensing.

Brewing Process

Standard brewing procedure for K-Cup pods.

1. Lift handle to open brew chamber.
2. Insert K-Cup pod into holder.
3. Close handle firmly until it locks.
4. Place mug on drip tray.
5. Press desired brew size button (Small/Medium/Large).
6. Brewing begins automatically; completes in under 1 minute.
7. Remove mug when brewing finishes.

Tip: Preheat mug with hot water for optimal coffee temperature.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Daily: Wipe exterior with damp cloth.
2. Weekly: Clean water reservoir and drip tray.
3. Monthly: Clean brew chamber and needle.
4. As needed: Descale when indicator light appears.

WARNING! Unplug before cleaning. Do not immerse in water.

Descaling Procedure

Descale every 3-6 months or when descale light appears.

1. Prepare descaling solution or white vinegar mixture.
2. Fill reservoir with descaling solution.
3. Place large container on drip tray.
4. Press and hold small and medium brew buttons for 3 seconds.
5. Press brew button to start descaling cycle.
6. Repeat with fresh water to rinse system.
7. Reset descale indicator when complete.

CAUTION! Use only Keurig descaling solution or approved alternatives.

Regulatory Information

UL listed; FCC Part 15 compliant. Copyright © Keurig Green Mountain, Inc. For support, visit www.keurig.com or contact 1-866-901-2739. This device complies with part 15 of the FCC Rules.

Troubleshooting

Reset: Unplug for 30 seconds, then restart.

Service: 1-866-901-2739; www.keurig.com