Keurig Operating Manual B60

The Keurig B60 is a premium single-serve coffee brewing system featuring programmable settings, multiple cup sizes, removable drip tray, water reservoir, descaling function, auto on/off, and energy saving mode. Designed for home and office use with 120V AC power. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Brew chamber, Water reservoir, Drip tray, Control panel, Power button, Cup size buttons, Display screen.

Installation

Unpack and inspect contents. Place on clean, level surface.

1. Remove all packaging materials from brewer and components.
2. Wash water reservoir with warm soapy water, rinse thoroughly.
3. Place brewer on stable, level counter away from heat sources.
4. Fill water reservoir with fresh cold water and replace on brewer.
5. Plug into standard 120V AC outlet.

WARNING! Do not use without water in reservoir. Keep away from children.

First-Time Setup

Prime the brewing system before first use.

1. Press POWER button to turn on brewer.
2. Lift and close brew handle without K-Cup pod.
3. Place mug on drip tray.
4. Press 8oz brew button to run water through system.
5. Repeat process 2-3 times to prime system completely.
6. Brewer is now ready for first K-Cup pod.

CAUTION! Use only Keurig-approved K-Cup pods. Do not use ground coffee.

Specifications

• Model: Keurig B60 Special Edition
• Water Reservoir: 48 oz removable tank
• Brew Sizes: 6oz, 8oz, 10oz (programmable)
• Power: 120V AC, 60Hz, 1470W
• Dimensions: 13.3" H x 10.2" W x 13.1" D
• Weight: 9.5 lbs
• Brew Time: Under 1 minute
• Auto Off: Programmable (2 hours default)
• Warranty: 1 year limited

Controls and Settings

Access settings via control panel buttons and display.

Control Panel: POWER, 6oz, 8oz, 10oz brew buttons, ADD WATER indicator, DESCALING indicator.

Programming: Hold brew button for 3 seconds to program cup size. Auto Off: Press and hold POWER for 3 seconds to cycle through auto-off options (2hr, 90min, 60min, 30min, Off). Display: Shows ready status, programming mode, add water alert, descaling reminder.

Using the Brewer

Brewing with K-Cup pods.

1. Press POWER button - brewer will heat (about 3 minutes).
2. Lift brew handle and insert K-Cup pod.
3. Close brew handle firmly.
4. Place mug on drip tray.
5. Press desired brew size button (6oz, 8oz, 10oz).
6. Brewing completes automatically.
7. Lift handle to eject used pod into storage compartment.

Tip: For stronger coffee, use smaller brew size with same pod.

Maintenance & Cleaning

Regular maintenance ensures optimal performance.

1. Daily: Wipe exterior with damp cloth.
2. Weekly: Remove and clean drip tray and reservoir.
3. Monthly: Clean brew chamber with paper clip if needed.
4. Descale: When indicator light appears (every 3-6 months).
5. Water Filter: Replace every 2 months or 60 tank refills.

WARNING! Unplug brewer before cleaning. Never immerse in water.

Descaling Procedure

Required when descale indicator illuminates.

1. Empty water reservoir and fill with descaling solution.
2. Place large mug (at least 16oz) on drip tray.
3. Press and hold 8oz and 10oz buttons for 3 seconds.
4. Press 10oz button to start descaling cycle.
5. Repeat until ADD WATER light appears.
6. Rinse reservoir thoroughly and fill with fresh water.
7. Run multiple brew cycles with fresh water to rinse system.

CAUTION! Use only Keurig descaling solution. Follow instructions carefully.

Care Instructions

Unplug before cleaning. Wipe with damp cloth only; no abrasive cleaners.

CAUTION! Do not use harsh chemicals; keep electrical components dry.

Regulatory Information

UL listed; complies with FCC Part 15. Copyright © Keurig Green Mountain, Inc. For support, visit www.keurig.com or contact 1-866-901-2739. This appliance is for household use only.

Troubleshooting

Reset: Unplug for 2 minutes then restart.

Service: 1-866-901-2739; www.keurig.com